 |
 |
 |
| |
 |
|
| |
PLCC Extractor
 The spring extractor is designed especially for removing PLCC from sockets without damaging components.
Price : $7.50 USD |
|
| |
|
|
 |
|
 |
|
 |
|
 |
 |
|
|
|
|
|
An all-in-one debugger/programmer solution the MPLAB ICD 2
is a low cost, real-time debugger and programmer for selected PICmicro MCUs. Using Microchip
Technology's proprietary In-Circuit Debug functions, programs can be downloaded, executed in real time and examined in detail using the debug functions of MPLAB. Watch variables and breakpoints can be set from symbolic labels in C or assembly source code, and single stepping can be done through C source line, assembly code level, or from a mixed C source and generated assembly level listing. MPLAB ICD 2 can also be used as a development programmer for supported PICmicro MCUs.
The secret behind In Circuit Debugging is the two dedicated hardware lines (microcontroller pins used only during debugging mode) that allow in circuit serial programming (ICSP) of the device and debugging capability through proprietary firmware. The ICD 2 debug features are built into the microcontroller and activated by programming the debug code into the target processor. There is some shared overhead expense that includes one stack level, some general purpose file registers and a small area of program memory when in the debug mode.
Compatible Microchip PIC ICD2 Debuggerr and Programmer Price : $70.00 EUR |
|
|
|
|
BASIC Stamp BS2SX-IC
Using Ubicom's microcontroller, the BS2SX-IC improved speed, larger program memory, and fastest serial I/O than all BASIC Stamps except for the BS2p. Great solution for those needing more horsepower than a BS2-IC (2.5 times faster). For even higher-performance, you may upgrade to the BS2p
BASIC Stamp BS2SX-IC Price : $24.00 USD |
|
|
|
|
BASIC Stamp 2p40-Pin (OEM board) BS2P40-IC
The BASIC Stamp 2p modules represent the next generation in Stamp technology. They run faster processors that are more efficient and have more program memory than ever before.
Many new powerful commands for I2C, LCD panels and One Wire devices (such as the iButton) are built-into the Stamp 2p modules.- BASIC Stamp 2p-40 has several advantages over all previous BASIC Stamps. It is 3 times faster than a BS2 and 20% faster than the BS2-SX. Commands for interfacing with parallel LCDs, I2C devices and Dallas Semiconductor 1-Wire parts have been added along with a polled interrupt capability. Since it is a 40-pin module, you also get double the number of I/O pins: 32, for your application.
BASIC Stamp 2p40-Pin (OEM board) BS2P40-IC $32.50 USD |
|
|
|
|
PLCC , DIP , TSOP Chip
W 27C512-45Z ( DIP 28 )
W 29C020C-90B ( DIP 32 )
AT 49F040 ( TSOP 32 )
W 29C040 ( DIP 32 )
M 27C1024 10F1 ( DIP 40 )
AT 27C1024-70JC ( PLCC 44 )
KM 62256ALP-10 ( DIP 28 )
AT 49F002 ( PLCC 32 )
AT 49F002 ( TSOP 32 )
AT 49F040 ( PLCC 32 )
AT 89S52 ( DIP 40 )
AT 89S51( DIP 40 )
|
|
|
|
|
Willem EPROM Programmer (PCB4C) Developed Board (June 2005)
Programming EPROM, EEPROM, FLASH Burner (Vpp 12.5V,21V,25V)
Support CHIPS (EPROM, EEPROM, FLASH, I2C,PIC, MCS-51,AVR, 93Cxx, ISP)
Additional support DIP32 to PLCC32 and Firmware HUB/LPC on board.
Fast programming time
. It is more STABLE than PCB3B (Standard) and Enhanced Willem
. It can program up to 30% FASTER more than v. PCB3B and Enhanced Willem
It can select use the power supply from a USB port or DC Adapter by setting jumper
It can set changes to be PCB3B or PCB4C by using jumper setting (when wish use Software of the ordinary) |
|
|
|
|
Willem EPROM Programmer (PCB3B/PCB3.5) Developed Board (February/2005)
Programming EPROM, EEPROM, FLASH Burnner (Vpp 12.5V,21V,25V)
Support CHIPS (EPROM, EEPROM, FLASH, I2C,PIC, MCS-51,AVR, 93Cxx, ISP)
The hardware PCB3B/PCB35 is more STABLE than PCB3B
It can program 30% faster than PCB3B or PCB3B+
It can use the power supply from a USB port or AC Adapter if needed
It can set changes to PCB3B or PCB3.5 using jumper setting if needed
Software willem PCB35A version 0.98b is perfectly compatible with Hardware PCB3.5 (Advances)
. Software Version 0.98a ( 0.98a[alpha] )
. Software Version (0.98ap) *** CAN UNLOCK AM29F040B ***
. Software Version 0.97j
Willem EPROM Software Operating Manual(included in CD)
Normally products that have only USB power cannot use Vcc > 5VDC. Our product provides a DC power port, so it can use VCC more than 5VDC(advantage).
The back circuit board is covered by the plastic board that is neat and completely protected from a short circuit. (value added) |
|
|
|
|
Willem EPROM Programmer (PCB3B+)
(The original have developed from Version. PCB3B)
It is mainly used for programming BIOS flash memory, It can program EPROM, EEEPROM, EEPROM, Flash Memory, Serial (I2C) EEPROM, Microwire EEPROM, Microchip PIC, Serial Peripheral Interface (SPI), Test nonvolatile SRAM, static RAM, and Micro controllers MCS-51, MCS-48...(an adapter is required), etc.
It can support : Eprom 27XXX EEprom 28C Eprom Flash W27EXXX Eprom 27CXXX EEprom AT27SFXXX Eprom Flash SST27SFXXX SRAM 61/62 Eprom Flash 28F DS12XX Eprom Flash SST28 SST29VF Eprom Flash 29F SST39LF Eprom Flash 39SF SYNCMOS F29F31XXX Eprom Flash 49F Eprom Flash MX29F Eprom Flash AM29F Eprom Flash AT49 Eprom Flash ASD AE49F2008 Eprom Flash AMIC 29F Eprom Flash SYNCMOS 29 Eprom Flash AT29 Eprom Flash ASD AE29 Eprom Flash W29EE Eprom Flash W29C Eprom Flash SSSPH 29EE |
|
|
|
|
|
You are buying directly from the manufacturer
